Felipe
a05ac96d97
- Added .devcontainer configuration for development environment. - Created .gitignore to exclude unnecessary files. - Configured C/C++ properties for ESP-IDF in VSCode. - Set up launch configurations for debugging. - Defined project settings for ESP-IDF in VSCode. - Created CMakeLists.txt for project build configuration. - Added README.md with project overview and usage instructions. - Established dependencies for Zigbee libraries in dependencies.lock. - Implemented main application logic in esp_zb_switch.c and esp_zb_switch.h. - Developed switch driver functionality in switch_driver.c and switch_driver.h. - Configured partition table in partitions.csv for NVS and application storage. - Set default SDK configuration in sdkconfig.defaults for project settings.
75 lines
5.5 KiB
Markdown
75 lines
5.5 KiB
Markdown
| Supported Targets | ESP32-C5 | ESP32-C6 | ESP32-H2 |
|
|
| ----------------- | -------- | -------- | -------- |
|
|
|
|
# Light Switch Example
|
|
|
|
This test code shows how to configure Zigbee Coordinator and use it as an HA on/off_switch.
|
|
|
|
The ESP Zigbee SDK provides more examples and tools for productization:
|
|
* [ESP Zigbee SDK Docs](https://docs.espressif.com/projects/esp-zigbee-sdk)
|
|
* [ESP Zigbee SDK Repo](https://github.com/espressif/esp-zigbee-sdk)
|
|
|
|
## Hardware Required
|
|
|
|
* One development board with ESP32-H2 SoC acting as Zigbee Coordinator (loaded with HA_on_off_switch)
|
|
* A USB cable for power supply and programming
|
|
* Choose another ESP32-H2 as Zigbee end-device (see [HA_on_off_light](../HA_on_off_light/))
|
|
|
|
## Configure the project
|
|
|
|
Before project configuration and build, make sure to set the correct chip target using `idf.py --preview set-target TARGET` command.
|
|
|
|
## Erase the NVRAM
|
|
|
|
Before flash it to the board, it is recommended to erase NVRAM if user doesn't want to keep the previous examples or other projects stored info using `idf.py -p PORT erase-flash`
|
|
|
|
## Build and Flash
|
|
|
|
Build the project, flash it to the board, and start the monitor tool to view the serial output by running `idf.py -p PORT flash monitor`.
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
## Example Output
|
|
|
|
As you run the example, you will see the following log:
|
|
|
|
```
|
|
I (441) main_task: Started on CPU0
|
|
I (441) main_task: Calling app_main()
|
|
I (461) phy: phy_version: 230,2, 9aae6ea, Jan 15 2024, 11:17:12
|
|
I (461) phy: libbtbb version: 944f18e, Jan 15 2024, 11:17:25
|
|
I (471) main_task: Returned from app_main()
|
|
I (601) ESP_ZB_ON_OFF_SWITCH: ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
|
|
I (601) ESP_ZB_ON_OFF_SWITCH: Initialize Zigbee stack
|
|
I (611) gpio: GPIO[9]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:2
|
|
I (611) ESP_ZB_ON_OFF_SWITCH: Deferred driver initialization successful
|
|
I (621) ESP_ZB_ON_OFF_SWITCH: Device started up in factory-reset mode
|
|
I (621) ESP_ZB_ON_OFF_SWITCH: Start network formation
|
|
W (781) ESP_ZB_ON_OFF_SWITCH: Network(0x13af) closed, devices joining not allowed.
|
|
I (781) ESP_ZB_ON_OFF_SWITCH: Formed network successfully (Extended PAN ID: 74:4d:bd:ff:fe:63:f7:30, PAN ID: 0x13af, Channel:13, Short Address: 0x0000)
|
|
I (1391) ESP_ZB_ON_OFF_SWITCH: Network(0x13af) is open for 180 seconds
|
|
I (1391) ESP_ZB_ON_OFF_SWITCH: Network steering started
|
|
I (9561) ESP_ZB_ON_OFF_SWITCH: ZDO signal: NWK Device Associated (0x12), status: ESP_OK
|
|
I (9561) ESP_ZB_ON_OFF_SWITCH: ZDO signal: ZDO Device Update (0x30), status: ESP_OK
|
|
I (9601) ESP_ZB_ON_OFF_SWITCH: New device commissioned or rejoined (short: 0x7c16)
|
|
I (9671) ESP_ZB_ON_OFF_SWITCH: Found light
|
|
I (9671) ESP_ZB_ON_OFF_SWITCH: Try to bind On/Off
|
|
I (9681) ESP_ZB_ON_OFF_SWITCH: Bound successfully!
|
|
I (9681) ESP_ZB_ON_OFF_SWITCH: The light originating from address(0x7c16) on endpoint(10)
|
|
I (9751) ESP_ZB_ON_OFF_SWITCH: ZDO signal: ZDO Device Authorized (0x2f), status: ESP_OK
|
|
I (9781) ESP_ZB_ON_OFF_SWITCH: Network(0x13af) is open for 180 seconds
|
|
I (16451) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
|
|
I (17011) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
|
|
I (17441) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
|
|
I (17831) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
|
|
```
|
|
|
|
## Light Control Functions
|
|
|
|
* By toggling the switch button (BOOT) on this board, the LED on the board loaded with the `HA_on_off_light` example will turn on and off.
|
|
|
|
|
|
## Troubleshooting
|
|
|
|
For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|